Differences

This shows you the differences between two versions of the page.

--- on_sky_testing [2025/11/21 15:46] – holtz
+++ on_sky_testing [2026/06/03 13:25] (current) – holtz
@@ Line 1: / Line 1: @@
+====June 2026====
+Various work:
+- the telescope started to oscillate in the past several weeks, evident in the Planewave tracking plots. We ran a quick tuning, but no change. We ran a thorough tuning (couple hours), also no change, but upon rebooting pwi1m computer, problem seems to have gone away. Consulting Planewave (Josh Persson), this is not expected, so unclear what was/is going on!
+- we installed a new stage for the iodine cell; previous stage was damaged and shipped to Thorlabs for repair. We used the bright LED source through a 10-micron fiber in the cal channel to project the beam through the system. We attached a card to front of iodine cell with a cross in the middle, and attempted
+to position the cell (in height) to center the beam on the spot; subsequently, determined stage postion to the the same in left-right motion. Connected the cell heaters/sensors to the TC300; reset to dual channel operation and PT100 sensors (black and white wires).
+- using 10 micron fiber with calibration source, investigated cal channel image quality, and image quality through iodine cell. Found that cal channel image quality was very poor. Attempted adjustment of both collimator and camera lenses and was unable to make any significant improvements. NOTE; we don't really care about image quality in cal channel because it is a diffuse source for calibration observations, but we wanted to get decent images to determine whether they are changed through iodine cell. Called Edmund Scientific, who advised that the doublets should be oriented with curved sides towards the image source and output image, backwards from how they were installed, so reversed the optics in their cells and reinstalled. Images better, but still poor. Did not attempt to improve the images, but determined that adding iodine cell only made minor changes to the image!  So cautiously optimistic.
+- redetermined calibration spot and hole positions. Focussed guide camera.
+- connected the QHY600 USB directly to the computer, rather than running through the Wanderer, in an attempt to cure the disconnects we have been getting
+- inspected Shelyak calibration source due to no LED light and determined that indeed, no LEDs appear to be coming on inside the unit. Emailed Shelyak.
+- took pixel flats with liquid cooled QHY600. This was achieved using a LED penlight wrapped in some bubble wrap and inserted into the upper light feed without moving anything in the spectrograph. Took 101 .0005s exposures
+- checked lower dome, which wouldn't open, even though it hasn't been used since Ben last looked at it and claimed it was fixed and working. Perhaps there is some thermal effect. When it gets in this tightly wrapped state, a screwdriver can be inserted in the right side to push the spring loaded catch down, after which you can pull on the cable/push shutter to loosen the system, after which it worked. Experimented with software for safe use of lower dome shutter. When it does fail, it always seems to be in that it won't open, but closes fine, so perhaps the episodic failures are not a show stopper (Bill suggests that running the motor and having the couple slip won't damage the coupler). Otherwise, software seemed to work ok, although there was one instance where, after opening, software thought is was closed, so automatic closing didn't proceed as it should have. Probably should triple-check this!  Implemented some new supported actions in dome driver to allow for easier testing by setting open/close time for both shutters to a shorter value so that they don't have to go all of the way.
+- at end of run, inspected calibration frames and see apparent drop in flux from previous week, especially in flats, but also in ThAr, with drop in both cal channel and direct channel. Lots of investigation followed, determined that fluxes can change with reseating of fiber in cal source, although still couldn't recover previous fluxes. Did fiber inspection and cleaning using APOGEE fiber microscope and cleaning device (with assistance from Jimmy Davidson), found some of the fibers pretty dirty, but didn't make dramatic changes in flux. Flipped the bifurcated fibers as one test. Direct fiber still much brighter in flats, but not nearly so much in ThAr? Final tests suggest significant change in flats but less in ThAr? Not clear what is going on, but maybe the illumination in the cal source is sufficiently non-uniform to make small changes in fiber placement significant, especially for quartz lamp? But swapping bifurcated fiber didn't seem to change the relative brightness dramatically. Maybe some issues with quartz lamp?
+====April 2026====
+A new iodine cell was installed.
+We implemented a shutter in the direct calibration channel.
+We got the repaired liquid cooled CCD back from QHY and installed it, along with the TCube Edge chiller.
+When revisiting spectrograph focus, the Esatto focuser would intermittently time out. As a result, it's uncertain whether the reported focus position is repeatable, e.g., after homing the focuser. Given potential repeatability issues, the focuser was just moved until acceptable images were reached, which is at a currently reported value of 398000. After settling on that, the Esattor focuser was powered off through the Wanderer PowerBox to remove the light source. A final image at this focus is UT260424/specfoc.0035.fits. 2D profiles for 5 ThAr lines, and 1D FWHM are as follows:
+{{:test:UT260424_focus2d.png?direct&400}}
+{{:test:UT260424_focus1d.png?direct&400}}
 ====November 2025====
 Enclosure box installed 11/18-29. Required taking ferrule out to run through box, so location of traces, etc. changed. Installed 4 temperature sensors inside the box. Cleaned up room and put spare parts on shelf and in drawers.  Installed pass-thrus for cables on FPUs. Connected big dome fan to outlet #10.
-Spectrograph refocussed.
+Spectrograph refocussed. Images look more circular in middle of chip at lower focus values, but extracted images show more variation in resolution at the lower values.
+Images from 433000 (left) to 438000 (right) in steps of 1000 near center of chip:
+{{:test:specfoc_433000_438000.png?direct&400}}
+Extracted FWHM/Resolution from the same sequence:
+|{{:test:specfoc_433000.png?direct&250}}|{{:test:specfoc_434000.png?direct&250}}|{{:test:specfoc_435000.png?direct&250}}|{{:test:specfoc_436000.png?direct&250}}|{{:test:specfoc_437000.png?direct&250}}|{{:test:specfoc_438000.png?direct&250}}|
+Not overly satisfying, but adopted 437000.
 ====Guiding tests====