tmo-wiki

User Tools

Site Tools

Trace:
hardware

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
hardware [2023/05/04 03:27] – holtzhardware [2025/06/10 20:40] (current) – holtz
Line 1: Line 1:
-== Telescope ==+=== Telescope === 
 The telescope is a 24" (61cm) Boller and Chivens reflector, serial number 3480. It was delivered in early 1967. It is an equatorial mount, with the RA counterweights in the base and the declination counterweights attached to the rear of the tube.  The telescope is a 24" (61cm) Boller and Chivens reflector, serial number 3480. It was delivered in early 1967. It is an equatorial mount, with the RA counterweights in the base and the declination counterweights attached to the rear of the tube. 
 [attachment:"UoR24in manual.pdf" Manual from similar University of Rochester telescope.] The original manual furnished with the NMSU telescope has been additionally scanned as a PDF. [attachment:"UoR24in manual.pdf" Manual from similar University of Rochester telescope.] The original manual furnished with the NMSU telescope has been additionally scanned as a PDF.
Line 5: Line 6:
  
 Mounted on the side of the telescope is a 6" two-element refractor guide scope. Mounted on the side of the telescope is a 6" two-element refractor guide scope.
 +
 +
 +The telescope was upgraded around 2010: the analog motors were replaced with digital servo motors, and the gear system replaced with a belt drive system, using 3/8" wide trapezoidal belts. On the RA drive, the motor wheel has 15 teeth, while the wheel on the RA worm has 30 teeth.
  
 Telescope communication and control is via a [[http://www.siderealtechnology.com/ |Sidereal Technology Servo Controller II]]. Telescope communication and control is via a [[http://www.siderealtechnology.com/ |Sidereal Technology Servo Controller II]].
 +
 +Although the SciTech controller can independently control the telescope, we conntinue to power up the Boller and Chivens system for several reasons: 1) it activates the torque motors that may help to push against the worm drive, 2) it activates the telescope hardware horizon limits. There is a relay attached to one of the web power switches which turns on the telescope power. There is a second relay attached to a separate controllable outlet that can be used to override the hardware limits; this must be used only with great understanding and care!
  
 Instrumentation is mounted at the Newtonian focus at the front of the telescope. Instrumentation is mounted at the Newtonian focus at the front of the telescope.
  
-== Focuser ==+=== Focuser ===
  
 The focuser is an Optec TCF-S. The focuser is an Optec TCF-S.
  
-== Filters and filter wheel ==+=== Filters and filter wheel ===
  
 Filter wheel is a Finger Lakes Instrumentation Centerline CL-1-14, purchased through Starizona summer/fall 2021. FLI software and Centerline software installed from FLI web site. This is a two-wheel filter wheel, with 7 slots (0-6) in each wheel. Installed ugriz, Halpha in slots 1-6 wheel0, BVR, D25, D38, and DARK in slots 1-6 wheel 1.  Filter wheel is a Finger Lakes Instrumentation Centerline CL-1-14, purchased through Starizona summer/fall 2021. FLI software and Centerline software installed from FLI web site. This is a two-wheel filter wheel, with 7 slots (0-6) in each wheel. Installed ugriz, Halpha in slots 1-6 wheel0, BVR, D25, D38, and DARK in slots 1-6 wheel 1. 
Line 23: Line 29:
  
  
-== Camera ==+=== Camera ===
  
 QHY 600 installed in spring 2021, purchased from OPT (along with a QHY CFW-3 filter wheel). This is a CMOS camera that uses a Sony IMX 455 sensor, with 9576 x 6388 3.76 micron pixels. QHY software allows for 1x1 and 2x2 binning. Given the small pixels, the latter is used. QHY 600 installed in spring 2021, purchased from OPT (along with a QHY CFW-3 filter wheel). This is a CMOS camera that uses a Sony IMX 455 sensor, with 9576 x 6388 3.76 micron pixels. QHY software allows for 1x1 and 2x2 binning. Given the small pixels, the latter is used.
Line 31: Line 37:
 Camera is cooled thermoelectrically. Typical set point is -12 C which can be reached year-round; of course, could go significantly colder in winter. Camera is cooled thermoelectrically. Typical set point is -12 C which can be reached year-round; of course, could go significantly colder in winter.
  
-== Guider ==+We  have had issues with being unable to connect to the camera after computer reboots, unless the USB cable is physically disconnected and reconnected. In October 2023, we installed a Wanderer Ultimate PowerBox V2 to be able to do this remotely (although, after installing this, the camera seems to come up on reboot!). There is a Wanderer Console software installed; start it and choose the WandererBox Ultimate V2 tab. You need to connect to the device (COM7 on 10/23), after which you  can plug/unplug the camera which is connected to USB 3-1.  
 + 
 +=== Guider ===
  
 Because of concerns of too much back focal distance with FLI centerline and offset guider, guider moved to 6" finder scope spring 2021. Guide camera is Starlight Xpress Ultrastar Pro, purchased from Starizona summer/fall 2021, installed 10/21. Because of concerns of too much back focal distance with FLI centerline and offset guider, guider moved to 6" finder scope spring 2021. Guide camera is Starlight Xpress Ultrastar Pro, purchased from Starizona summer/fall 2021, installed 10/21.
  
  
-=== obsolete ===+== obsolete ==
  
 Previous camera was a QSI 583 science camera, connected with a Type A USB cable. The science CCD is usually set to a temperature of -20° C, but on very hot nights may not reach that temperature. Typical field of view is 18.4x13.8 arcminutes, with an unbinned plate scale of ~0.33"/pixel and an array size of 3326x2504 px. Available filters are B,V,R,I, and clear. Typical read noise is ~8 electrons. QSI583 has 5-slot filter wheel, offering B,V,R,I, and clear filters. Previous camera was a QSI 583 science camera, connected with a Type A USB cable. The science CCD is usually set to a temperature of -20° C, but on very hot nights may not reach that temperature. Typical field of view is 18.4x13.8 arcminutes, with an unbinned plate scale of ~0.33"/pixel and an array size of 3326x2504 px. Available filters are B,V,R,I, and clear. Typical read noise is ~8 electrons. QSI583 has 5-slot filter wheel, offering B,V,R,I, and clear filters.
Line 45: Line 53:
  
  
-== Dome ==+=== Dome ===
  
 The dome is made of white fiberglass. The dome slit home position is east, facing the Organ Mountains, and the park position is slightly left of this.( "homing" the dome basically tells it where it is; parking is just "here's where I want to leave it".) The dome drive motor (Dayton DC Gearmotor SLAF6, 12V, 12.6A) is located on the northern side of the room, and is fitted with a 10x3" drive wheel with 1" central bore and a key slot. A spring provides adjustable tension to hold the drive wheel against the dome. Dome slit manual controls are located to the right of the slit motor, and forward/reverse rotation controls are located directly under the dome motor. The dome is made of white fiberglass. The dome slit home position is east, facing the Organ Mountains, and the park position is slightly left of this.( "homing" the dome basically tells it where it is; parking is just "here's where I want to leave it".) The dome drive motor (Dayton DC Gearmotor SLAF6, 12V, 12.6A) is located on the northern side of the room, and is fitted with a 10x3" drive wheel with 1" central bore and a key slot. A spring provides adjustable tension to hold the drive wheel against the dome. Dome slit manual controls are located to the right of the slit motor, and forward/reverse rotation controls are located directly under the dome motor.
  
 Dome shutter power is provided by a 15W/1A amorphous solar panel (NPower 15W Solar 12V Battery Charger) on the exterior of the dome, approximately 90° to the right of the slit. This solar panel is protected with 1/4" plexiglass and a styrofoam shock absorber. There are two spare solar panels in the building. Power is routed through a charge controller (7A max) to a 12V battery mounted to the interior of the dome; if replacing this, make sure that the wires are secured such that they will not catch on anything during dome rotation. In case of emergency, a 12V battery trickle charger is stored in the computer room. Dome shutter power is provided by a 15W/1A amorphous solar panel (NPower 15W Solar 12V Battery Charger) on the exterior of the dome, approximately 90° to the right of the slit. This solar panel is protected with 1/4" plexiglass and a styrofoam shock absorber. There are two spare solar panels in the building. Power is routed through a charge controller (7A max) to a 12V battery mounted to the interior of the dome; if replacing this, make sure that the wires are secured such that they will not catch on anything during dome rotation. In case of emergency, a 12V battery trickle charger is stored in the computer room.
 +
 +The dome shutter has limit switches which are triggered at either end of travel by small ramps that are welded to the dome that push up on one of two roller switches mounted on the right side of the shutter. There is also a large double-direction switch that kills power to the motor in the event that the limit switches fail to do so through the control card, although this switch needs to be adjusted so that it gets triggered before the shutter is sufficiently closed to prevent further motion.
  
 The dome communicates with the other electronics via a magnetic induction loop. This is the thin wire on dowels on the ledge running around the bottom of the dome interior. Be careful around the wire, as it could break easily. Automation is provided by a [[http://diffractionlimited.com/product/maxdome-ii-observatory-dome-control-system/ |Diffraction Limited Maxdome II dome controller]]. The two Maxdome circuit boards are encased in metal boxes, one next to the manual rotation controls and one inside the manual slit control box. These circuit boards have status LEDs, visible through small holes in the boxes; this can be useful for troubleshooting. See below for more details on these cards The dome communicates with the other electronics via a magnetic induction loop. This is the thin wire on dowels on the ledge running around the bottom of the dome interior. Be careful around the wire, as it could break easily. Automation is provided by a [[http://diffractionlimited.com/product/maxdome-ii-observatory-dome-control-system/ |Diffraction Limited Maxdome II dome controller]]. The two Maxdome circuit boards are encased in metal boxes, one next to the manual rotation controls and one inside the manual slit control box. These circuit boards have status LEDs, visible through small holes in the boxes; this can be useful for troubleshooting. See below for more details on these cards
  
-The dome rests on 13 4"x1.5" rolling bearing phenolic [[https://www.grainger.com/product/GRAINGER-APPROVED-4-Caster-Wheel-1G450 |caster wheels]] with a 1 5/8" hub length and 3/8" bore. The axles are 2.5" long hex bolts (3/8" diam, about half an inch of thread.) There is an approximately 5" clearance between the bottom of the dome and the ledge; a typical emergency tire-replacement jack is sufficient to raise the dome enough for wheel replacement. There are also several identical horizontal wheels, which are not load bearing.+The dome rests on 13 4"x1.5" rolling bearing phenolic [[https://www.grainger.com/product/Caster-Wheel-4-in-Wheel-Dia-55KC34?opr=PDPDAM&analytics=msubItems_1G450&position=1|caster wheels]] (link updated on May 3rd, 2024) with a 1 5/8" hub length and 3/8" bore. The axles are 2.5" long hex bolts (3/8" diam, about half an inch of thread.) There is an approximately 5" clearance between the bottom of the dome and the ledge; a typical emergency tire-replacement jack is sufficient to raise the dome enough for wheel replacement. There are also several identical horizontal wheels, which are not load bearing. 
 + 
 +Jon and Zach replaced the wheel that is south of due east on May 3rd, 2024. This failed again in early 2025, perhaps because the caster was compromised. New casters were purchased and welded into place by NMSU F&S, and new wheels installed (see maintenance log).
  
 Dome is controlled by ACP; don't connect to the dome in MaximDL. Note that the dome is set up such that it will automatically close if it does not detect a signal from the control computer; so if you're up there doing maintenance and open it to let some light in, make sure the computer is on so it doesn't close itself. Dome is controlled by ACP; don't connect to the dome in MaximDL. Note that the dome is set up such that it will automatically close if it does not detect a signal from the control computer; so if you're up there doing maintenance and open it to let some light in, make sure the computer is on so it doesn't close itself.
  
-==== Maxdome Card ====+== Maxdome Card ==
  
 After suffering a failure of the dome control card we ordered a new card from Diffraction Limited. Upon installing it the dome immediately started to rotate endlessly. Pressing the stop button did stop the rotation, but only for as long as it was held in. Upon releasing the button, the dome began to rotate again. After suffering a failure of the dome control card we ordered a new card from Diffraction Limited. Upon installing it the dome immediately started to rotate endlessly. Pressing the stop button did stop the rotation, but only for as long as it was held in. Upon releasing the button, the dome began to rotate again.
Line 72: Line 84:
  
  
-== Weather ==+=== Weather ===
  
 Weather sensing is provided by a [[http://diffractionlimited.com/product/boltwood-cloud-sensor-ii/ |Boltwood CloudSensor II]]. This will provide information regarding wind speed, humidity, cloud cover, temperature, rain, and dew point. If the weather is deemed unsafe, ACP Scheduler will not operate the observatory- it waits for at least ten minutes of continuous "safe" weather before attempting to observe. Note that the automatic weather script will trigger for unsafe weather even if you are observing manually. Nevertheless, you should probably not run Scheduler if it is likely to rain or the conditions look bad. Weather sensing is provided by a [[http://diffractionlimited.com/product/boltwood-cloud-sensor-ii/ |Boltwood CloudSensor II]]. This will provide information regarding wind speed, humidity, cloud cover, temperature, rain, and dew point. If the weather is deemed unsafe, ACP Scheduler will not operate the observatory- it waits for at least ten minutes of continuous "safe" weather before attempting to observe. Note that the automatic weather script will trigger for unsafe weather even if you are observing manually. Nevertheless, you should probably not run Scheduler if it is likely to rain or the conditions look bad.
  
-== Power ==+=== Power ===
  
 Power to the hardware, dome, and telescope are controlled through two internet-connected power strips. [[http://tmopower1.nmsu.edu |tmopower1]] is located next to the desk (western side of room). Most of the power sockets on the strips are labeled in the power control interfaces. Socket 1 controls the telescope power; note that turning this off will turn off power to TMOPower2 and all of its sockets! Socket 2 should never be left powered on! Power to the hardware, dome, and telescope are controlled through two internet-connected power strips. [[http://tmopower1.nmsu.edu |tmopower1]] is located next to the desk (western side of room). Most of the power sockets on the strips are labeled in the power control interfaces. Socket 1 controls the telescope power; note that turning this off will turn off power to TMOPower2 and all of its sockets! Socket 2 should never be left powered on!
Line 82: Line 94:
 [[http://tmopower2.nmsu.edu| tmopower2]] is physically mounted on the telescope itself, and controls power to the instrumentation and associated hardware. Note that this powerswitch is itself powered through the telescope power, so will only be reachable if the telescope power is on on TMOPower1. [[http://tmopower2.nmsu.edu| tmopower2]] is physically mounted on the telescope itself, and controls power to the instrumentation and associated hardware. Note that this powerswitch is itself powered through the telescope power, so will only be reachable if the telescope power is on on TMOPower1.
  
-== Other ==+=== Other ===
  
 Internet access is through a small wireless antenna on the southern side of the building, underneath the dome and pointed at the nearby radio tower. There have been instances where this antenna was vandalized or wind knocked it down; if this happens you may have little to no internet connectivity, which is bad.  Internet access is through a small wireless antenna on the southern side of the building, underneath the dome and pointed at the nearby radio tower. There have been instances where this antenna was vandalized or wind knocked it down; if this happens you may have little to no internet connectivity, which is bad. 
hardware.1683170865.txt.gz · Last modified: 2023/05/04 03:27 by holtz
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki