Differences

This shows you the differences between two versions of the page.

--- telescope_and_observatory_control [2024/05/24 16:23] – holtz
+++ telescope_and_observatory_control [2025/05/21 15:20] (current) – holtz
@@ Line 5: / Line 5: @@
 Telescope is a Planewave PW1000. It is controlled through the pwi1m computer in the 1m dome, running Windows. pwi1m has two network interfaces. One connects to the telescope internal network on 192.168.10.XXX. pwi1m is 192.168.10.40, the Maestro controller on the telescope is 192.168.10.50, and the OTA controller on the telescope is 192.168.10.60.
-Software control is through Planewave's PWI4 software. This runs  under Windows on pwi1m , and provides a graphical user interface, as well as an ASCOM driver and also a custom Planewave HTTP API.
+Software control is through Planewave's PWI4 software. This runs  under Windows on pwi1m, and provides a graphical user interface, as well as an ASCOM driver and also a custom Planewave HTTP API.
 Normal telescope control is done remotely through the ASCOM interface, but interacting with PWI4 directly provide additional functionality. In particular, PWI4 incorporates its own pointing model software.
@@ Line 13: / Line 13: @@
 ===== Camera control system =====
-Acquisition camera is connected to pwi1m via USB. PWI4 has the capability to connect to an ASCOM camera, and this is needed for doing pointing models
+Acquisition camera is connected to pwi1m via USB. PWI4 has the capability to connect to an ASCOM camera, and this is needed for doing pointing models.
-Normal camera control is done remotely throught the ASCOM interface. The camera ASCOM driver should be registered through ASCOM Remote to make it available through an ASCOM/Alpaca interface.
+Normal camera control is done remotely through the ASCOM interface. The camera ASCOM driver should be registered through ASCOM Remote to make it available through an ASCOM/Alpaca interface.
 ===== Observatory control system ======
@@ Line 33: / Line 33: @@
 -pin connector J808A : Watchdog (dome box needs +24V or else shutter will close on Automatic)
 | Dome box |         |  Peltec timer | | | |
-| 1        | gnd     |    18   |   15 |   gnd | 15 connects to 18 for ~4 minutes after power is dropped between A1 and A2 |
+| 1        | gnd, white     |    18   |   15 |   gnd | 15 connects to 18 for ~4 minutes after power is dropped between A1 and A2 |
-| 3        | +24V DC |    28   |   25 |  +24V | same for 25 and 18 |
+| 3        | +24V DC, purple |    28   |   25 |  +24V | same for 25 and 18 |
 |          |         |    A1   |   relay 5 | gnd | trigger for relay, must cycle every 3 minutes to keep dome open (but don't leave energized permanently! |
 |          |         |    A2   |  +24V | | same |
@@ Line 42: / Line 42: @@
 connector J805A : Supplies power and ground to box, and relay for dome power (org yel blu wires)
 |J805A pin | 9 pin connector | function | comment |
-| 4 | 4 | +24V | voltage always supplied |
+| 4 | 4 | +24V red | voltage always supplied |
-| 3 | 1 | gnd  | ground always supplied
+| 3 | 1 | gnd white | ground always supplied
 | 2 | 2 |relay 1 grey | trigger connects pin to ground |
 connector J806A : Supplies (redundant?) power and ground to box, and relay for dome direction (brn red grn wires)
 |J806A pin | 9 pin connector| function | comment |
-| 4 | 9 |+24 | voltage always supplied |
+| 4 | 9 |+24 red | voltage always supplied |
-| 3 | 8 | gnd | ground always supplied
+| 3 | 8 | gnd white | ground always supplied
 | 2 | 7 | relay 3 brown | trigger connects pin to ground |
@@ Line 55: / Line 55: @@
 | J807A pin| function | comment |
 | 2 | relay 2 purple | trigger connects pin to ground |
-| 3 | gnd| ground always supplied |
+| 3 | gnd black| ground always supplied |
 | 4 | relay 4 orange | trigger connects pin to ground |
-| 5 | gnd | ground always supplied |
+| 5 | gnd black | ground always supplied |
@@ Line 85: / Line 85: @@
 | grn | +DC   | 4 | red | RPi +5V |
+===== Cabling =====
+  - four-pin AMP to dome box
+  - four-pin AMP to dome box
+  - nine-pin AMP to dome box
+  - four-pin AMP to home sensor
+  - Ethernet cable
+  - power cord for power supply
+  - power cord for Raspberry Pi ?
+  - ground wire
+  - cable for lower dome
 ===== Old setup for relays =====
@@ Line 90: / Line 102: @@
 OLD Setup through Autoscope control box, which uses 5V Opto 22 relays.
-|OCS |  RPi |
+|OCS |RPi |
 |50 grn  | 5 | watchdog |
 |49 Pur  | 7 | |